How to test the humidity resistance of a 4 To 20mA Output DC Voltage Sensor?

Nov 16, 2026Leave a message

As a supplier of 4 to 20mA Output DC Voltage Sensor, I often get asked about testing the humidity resistance of these sensors. Since they're used in all sorts of environments, it's super important to ensure they can handle humidity without going haywire. In this post, I'll share a few ways to test the humidity resistance of a 4 to 20mA output DC voltage sensor.

Why Test Humidity Resistance?

Before we dive into the testing methods, let's talk about why it's necessary in the first place. Humidity can cause a bunch of problems for sensors. High humidity levels can lead to condensation on the sensor's components. That moisture can create short circuits, corrode the pins and circuits, and mess with the electrical properties of the materials inside the sensor. All these can result in inaccurate readings, reduced lifespan of the sensor, and even total failure.

So, if you're using these sensors in places like factories with high steam levels, storage areas where humidity isn't well - controlled, or near bodies of water, testing their humidity resistance is a must.

Testing Methods

1. Environmental Chamber Testing

One of the most reliable ways to test humidity resistance is by using an environmental chamber. These chambers allow you to precisely control the temperature and humidity levels inside.

First, you'll need to set the chamber to the baseline conditions. Usually, a temperature of around 25°C and a relative humidity (RH) of about 50% is a good starting point. Let the sensor sit in these conditions for a few hours to stabilize. During this time, take some baseline readings of the sensor's output.

High Voltage High Isolation Voltage Transducer

Next, start ramping up the humidity. You can increase the RH to 70%, then 80%, and finally 90%. At each step, let the sensor sit for at least 24 hours to ensure it reaches equilibrium with the new humidity conditions. Continuously monitor the sensor's 4 to 20mA output. Any significant deviation from the baseline readings could indicate that the sensor is being affected by the humidity.

After reaching the maximum humidity level, you can gradually decrease it back to the baseline. Keep monitoring the output to see if the sensor returns to its normal performance. If it does, it shows good humidity resistance.

2. Salt Spray Test (Modified)

The traditional salt spray test is mainly used to test corrosion resistance, but we can modify it to also assess humidity resistance.

Prepare a saltwater solution with a concentration of around 5% sodium chloride (NaCl). Place the sensor in a sealed container with a small dish of the saltwater solution. The saltwater will evaporate, increasing the humidity inside the container and also introducing some salt particles into the air.

Let the sensor stay in this environment for a specific period, say 48 hours. During this time, monitor the sensor's output. The salt particles can interact with the moisture on the sensor's surface, accelerating the corrosion process and simulating a harsh humid environment. If the sensor performs well and its output remains stable, it has good resistance to humidity - related corrosion.

3. Real - World Testing

There's no better way to test the humidity resistance of a sensor than in its actual working environment. If possible, install a few test sensors in areas with high humidity. For example, if your sensors are used in a greenhouse, the high humidity and moisture from watering are perfect for testing.

Monitor the sensors over an extended period, like a few weeks or months. Record any changes in their output. Compare the performance in different seasons or weather conditions. This will give you a real - world understanding of how the sensors hold up against humidity.

Factors Affecting Humidity Resistance

While testing, it's important to understand the factors that can affect a sensor's humidity resistance.

Sensor Design

The physical design of the sensor plays a huge role. Sensors with a hermetically sealed enclosure are generally more resistant to humidity since they prevent moisture from getting inside. On the other hand, sensors with open - air designs or exposed circuits are more vulnerable.

Materials Used

The materials used in the sensor also matter. Components made of corrosion - resistant materials like stainless steel or some special polymers can withstand humidity better. Conductive materials that are not easily oxidized are also preferred. For example, High Voltage High Isolation Voltage Transducer is designed with materials that can offer better resistance in humid environments.

Coating

Some sensors come with a protective coating. This coating can act as a barrier between the sensor's components and moisture in the air. It can be a conformal coating that covers the PCB or a hydrophobic coating on the outer surface of the sensor.

Interpreting Test Results

Once you've completed the tests, it's time to interpret the results.

  • No Deviation: If the sensor's output remains stable throughout the testing process, with less than a ±1% deviation from the baseline readings, it can be considered to have excellent humidity resistance. This means it can be used in most humid environments without any major issues.
  • Slight Deviation: A deviation of up to ±3% can still be acceptable in some applications. However, it might need some calibration or additional protection like a moisture - proof enclosure.
  • Significant Deviation: If the deviation is more than ±3%, it indicates that the sensor is highly affected by humidity. You might need to look for a different sensor model or find ways to improve its humidity resistance, such as adding a better coating or changing the design.

Improving Humidity Resistance

If your test results show that the sensor's humidity resistance could be better, there are a few things you can do.

  • Sealing: Make sure the sensor is properly sealed. You can use gaskets, O - rings, or epoxy to seal the enclosure. This will prevent moisture from entering the sensor.
  • Coating: Apply a conformal coating to the PCB. There are different types of conformal coatings available, such as acrylic, silicone, and urethane. Choose the one that suits your needs based on factors like flexibility, adhesion, and chemical resistance.
  • Desiccant: Place a desiccant inside the sensor's enclosure. Desiccants can absorb moisture from the air, keeping the internal environment dry.

Our Range of 4 to 20mA Output DC Voltage Sensors

We offer a wide range of 4 to 20mA Output Electrical Voltage Transducer, DC Voltage Transducer 4 - 20mA Analog Output, and DC Voltage Sensor with Analog Output. Our sensors are designed with high - quality materials and advanced manufacturing techniques to ensure good humidity resistance.

We've already conducted extensive humidity resistance tests on our products. Most of our sensors can easily withstand humidity levels of up to 90% without significant performance degradation. But if you need a sensor for an extremely harsh humid environment, we can customize the design and add additional protective measures to meet your requirements.

Contact Us for Procurement

If you're interested in our 4 to 20mA output DC voltage sensors, feel free to reach out. We're always ready to offer technical support, answer your questions, and provide samples for testing. Whether you need sensors for a small project or large - scale industrial applications, we can provide the right solution for you. Let's start a discussion and find the best sensor for your specific needs.

References

  • "Sensor Technology Handbook" by Jon Wilson
  • "Environmental Testing of Electronic Components" published by the Institute of Electrical and Electronics Engineers (IEEE)